Electrochemistry (part 3 of 3)
19 practice questions for Senior Chemistry II (Year 12, Grade 12) chemistry. Try each one, then open the answer for the explanation and a tip to remember it.
1.In electrolytic refining, where impure copper is purified by electrolysis, which electrode is the impure copper connected to?
- ABoth electrodes
- BEither electrode
- CThe (+) electrode
- DThe (−) electrode
Show the answer
Answer: C. The (+) electrode
The answer is the (+) electrode. Impure copper connected to the (+) electrode is oxidized as Cu → Cu²⁺ + 2e⁻ and dissolves. The dissolved Cu²⁺ gains electrons at the pure copper plate at the (−) electrode and is deposited as copper, so only pure copper builds up. If the impure copper were at the (−) electrode, it wouldn’t dissolve, and no refining would happen.
Remember: The side to dissolve away is (+); the side to build up is (−). It’s the same principle as plating.
Did you know? The sludge that collects under the (+) electrode (anode slime) contains precious metals such as gold and silver, so it is collected and sold separately.
2.How is aluminum produced industrially?
- ABy heating aluminum oxide with sugar
- BBy electrolyzing molten aluminum oxide
- CBy dissolving aluminum oxide in water and evaporating it
- DBy filtering aluminum ore through filter paper
Show the answer
Answer: B. By electrolyzing molten aluminum oxide
The answer is by electrolyzing molten aluminum oxide. Aluminum is very reactive, so it’s hard to reduce with carbon, and if you electrolyze an aqueous solution, water is reduced instead. So aluminum oxide is melted together with cryolite and electrolyzed. You can’t get the metal by dissolving it in water and evaporating, or by filtering.
Remember: Very reactive metals (Na, Al) are obtained by electrolyzing a ‘molten’ liquid with no water.
Did you know? Before Hall and Héroult each discovered this method in 1886, aluminum was treated like a precious metal; there’s a story that Napoleon III served his most honored guests with aluminum cutlery.
3.What is the overall reaction of a hydrogen fuel cell?
- AH₂ + Cl₂ → 2HCl
- B2H₂O → 2H₂ + O₂
- C2H₂ + O₂ → 2H₂O
- DCH₄ + 2O₂ → CO₂ + 2H₂O
Show the answer
Answer: C. 2H₂ + O₂ → 2H₂O
The answer is 2H₂ + O₂ → 2H₂O. In a hydrogen fuel cell, hydrogen is oxidized at the (−) electrode and oxygen is reduced at the (+) electrode, forming water overall, and electrical energy is obtained in the process. 2H₂O → 2H₂ + O₂ is the electrolysis of water, which goes in the opposite direction, so it’s wrong.
Remember: A fuel cell runs the electrolysis of water in reverse.
Did you know? The principle of the fuel cell was first demonstrated by experiment in 1839 by William Grove in Britain.
4.In a hydrogen fuel cell, what is supplied to the (−) electrode?
- AWater
- BOxygen
- CCarbon dioxide
- DHydrogen
Show the answer
Answer: D. Hydrogen
The answer is hydrogen. At the (−) electrode of a fuel cell, the fuel, hydrogen, loses electrons in an oxidation reaction (H₂ → 2H⁺ + 2e⁻). These electrons travel along the wire to the (+) electrode and reduce oxygen. Oxygen is supplied to the (+) electrode, and water is the substance produced by the reaction.
Remember: The fuel (hydrogen) gives away electrons, so it goes to (−); oxygen accepts electrons, so it goes to (+).
Did you know? Hydrogen is the most common element in the universe, but on Earth it’s mostly locked up in water and other compounds, so it has to be produced separately.
5.What type of reaction happens at the (+) electrode of a hydrogen fuel cell?
- AReduction of oxygen
- BOxidation of water
- CReduction of hydrogen
- DOxidation of hydrogen
Show the answer
Answer: A. Reduction of oxygen
The answer is reduction of oxygen. Reduction happens at the (+) electrode of a cell, and in a fuel cell, the oxygen supplied there gains electrons that came along the wire and is reduced (O₂ + 4H⁺ + 4e⁻ → 2H₂O). Oxidation of hydrogen happens at the (−) electrode, so it’s wrong.
Remember: The (+) electrode of a cell is always ‘reduction’. Oxygen is the side that accepts electrons.
Did you know? This electrode uses a platinum catalyst to help the reaction, and cutting down the amount of expensive platinum needed is a major research goal for fuel cells.
6.In a hydrogen fuel cell with a basic electrolyte, which is the correct (−) electrode reaction?
- AH₂ + 2OH⁻ → 2H₂O + 2e⁻
- B2H₂O → O₂ + 4H⁺ + 4e⁻
- CO₂ + 2H₂O + 4e⁻ → 4OH⁻
- D4OH⁻ → O₂ + 2H₂O + 4e⁻
Show the answer
Answer: A. H₂ + 2OH⁻ → 2H₂O + 2e⁻
The answer is H₂ + 2OH⁻ → 2H₂O + 2e⁻. Hydrogen is oxidized at the (−) electrode, and since a basic electrolyte has lots of OH⁻, hydrogen reacts with OH⁻ to form water and releases electrons. O₂ + 2H₂O + 4e⁻ → 4OH⁻ gains electrons, so it is the reduction at the (+) electrode.
Remember: If e⁻ is on the right (product side) of an equation, it’s oxidation; if it’s on the left, it’s reduction.
Did you know? Cells like this use potassium hydroxide solution as the electrolyte and are called ‘alkaline fuel cells’; they were also used to power the Apollo spacecraft.
7.What is an advantage of hydrogen fuel cells?
- AThe reaction product is water, so they release almost no air pollutants
- BThey make lots of carbon dioxide to help plants grow
- CThey don’t use hydrogen at all
- DThey work forever without recharging
Show the answer
Answer: A. The reaction product is water, so they release almost no air pollutants
The answer is that the reaction product is water, so they release almost no air pollutants. A hydrogen fuel cell gets electricity from the reaction 2H₂ + O₂ → 2H₂O, so no carbon dioxide comes out. The fuel, hydrogen, must be supplied continuously, so ‘they work forever without recharging’ is wrong.
Remember: A fuel cell isn’t recharged; it works only as long as fuel (hydrogen) keeps being supplied.
Did you know? Hydrogen cars use strong carbon-fiber tanks with hydrogen squeezed to about 700 atmospheres, to carry plenty of the light gas.
8.Why is a hydrogen fuel cell more energy-efficient than a thermal power plant that burns fuel?
- ABecause it uses no catalyst
- BBecause it first makes heat to turn a turbine
- CBecause it converts chemical energy directly into electrical energy without combustion
- DBecause hydrogen is heavier than oxygen
Show the answer
Answer: C. Because it converts chemical energy directly into electrical energy without combustion
The answer is that it converts chemical energy directly into electrical energy without combustion. A thermal power plant converts energy several times, chemical energy → heat → motion (turbine) → electricity, with large losses. A fuel cell skips these steps. Real fuel cells use catalysts such as platinum, so ‘it uses no catalyst’ is wrong.
Remember: The fewer energy conversion steps, the smaller the losses and the higher the efficiency.
Did you know? If the heat from a fuel cell is also used for heating and hot water, the overall energy use can reach around 80%.
9.Unlike primary cells, which are used once and thrown away, which is an example of a secondary (rechargeable) cell?
- AAlkaline battery
- BLithium-ion battery
- CZinc–carbon dry cell
- DMercury battery
Show the answer
Answer: B. Lithium-ion battery
The answer is the lithium-ion battery. A secondary cell can be used again and again because charging drives the reverse of the discharge reaction; the lithium-ion batteries in smartphones and laptops are the classic example. Zinc–carbon dry cells, alkaline batteries and mercury batteries are primary cells that are used once and thrown away.
Remember: Most everyday batteries sold as ‘dry cells’ are primary cells.
Did you know? Goodenough, Whittingham and Akira Yoshino, who developed the lithium-ion battery, shared the 2019 Nobel Prize in Chemistry.
10.Which secondary cell is widely used as a car starter battery?
- AZinc–carbon dry cell
- BLead–acid battery
- CVoltaic cell
- DHydrogen fuel cell
Show the answer
Answer: B. Lead–acid battery
The answer is the lead–acid battery. A lead–acid battery is a secondary cell that uses lead at the (−) electrode, lead(IV) oxide at the (+) electrode and dilute sulfuric acid as the electrolyte. It can deliver a large current and can be recharged, so it’s used to start cars. The zinc–carbon dry cell is a primary cell, and the hydrogen fuel cell works by being supplied with fuel, so they’re wrong.
Remember: When a lead–acid battery discharges, both electrodes turn into lead sulfate (PbSO₄).
Did you know? The lead–acid battery, invented by Planté in France in 1859, was the first rechargeable battery. It has been in use for more than 160 years.
Getting these right? In Valence, a correct answer earns research funds for your next card. Play free and set the quiz level to Chemistry II.
11.What happens when a secondary cell is charged?
- AChemical energy is turned into light energy
- BAll the substances in the cell disappear
- CExternal electrical energy drives the reverse of the discharge reaction
- DNew electrolyte must keep being added
Show the answer
Answer: C. External electrical energy drives the reverse of the discharge reaction
The answer is that external electrical energy drives the reverse of the discharge reaction. If discharging turned chemical energy into electrical energy, charging uses an external power supply to drive the reverse reaction and restore the reactants. So charging is a kind of electrolysis. Adding new electrolyte isn’t charging.
Remember: Charging = electrical energy → chemical energy, the opposite direction to discharging.
Did you know? In a lithium-ion battery, charging makes lithium ions slip in and hide between layers of graphite; when the battery is used, they come back out and travel to the other electrode.
12.What conditions are needed for iron to rust (corrode)?
- ALight and nitrogen
- BWater and oxygen
- CHydrogen and helium
- DNitrogen and carbon dioxide
Show the answer
Answer: B. Water and oxygen
The answer is water and oxygen. When water and oxygen are both present, iron loses electrons and is oxidized, forming rust (mainly iron oxide). With only water or only oxygen, it doesn’t rust easily. Nitrogen, carbon dioxide and helium aren’t conditions needed for iron to corrode.
Remember: ‘Both’ water and oxygen are needed. Blocking just one can slow corrosion.
Did you know? The Iron Pillar of Delhi in India has stood outdoors for more than 1,600 years with hardly any rust, so it has long been studied by scientists.
13.Why are blocks of zinc attached to the bottom of a ship’s steel hull?
- AZinc is oxidized before iron, preventing the iron from corroding
- BZinc is less reactive than iron, so it coats the iron
- CZinc turns seawater into fresh water
- DZinc makes the ship lighter
Show the answer
Answer: A. Zinc is oxidized before iron, preventing the iron from corroding
The answer is that zinc is oxidized before iron, preventing the iron from corroding. Zinc is more reactive than iron, so it gives up its own electrons and is oxidized instead, while the iron receives electrons and isn’t oxidized. This is called the sacrificial anode method. Zinc protects iron because it is ‘more’ reactive, so ‘less reactive’ is wrong.
Remember: A sacrificial metal must be ‘more’ reactive than the metal it protects.
Did you know? In 1824, Humphry Davy in Britain first proposed attaching pieces of zinc or iron to the copper bottoms of warships to reduce corrosion.
14.Why does zinc-coated (galvanized) steel resist rusting even when it’s scratched and the iron is exposed?
- AZinc absorbs all the water
- BZinc is more reactive than iron, so it is oxidized first
- CZinc is less reactive than iron
- DIron doesn’t react with oxygen at all
Show the answer
Answer: B. Zinc is more reactive than iron, so it is oxidized first
The answer is that zinc is more reactive than iron, so it is oxidized first. Even when galvanized steel is scratched and the iron is exposed, the surrounding zinc gives up electrons and is oxidized instead, so the iron is protected. In contrast, with tinplate (iron coated with tin), tin is less reactive than iron, so when it’s scratched the iron actually rusts faster.
Remember: Galvanized steel (zinc) is fine when scratched; tinplate (tin) rusts faster when scratched.
Did you know? Coating iron with zinc is called ‘galvanizing’. The name comes from Galvani, the Italian scientist famous for his experiments on frog legs.
15.How does painting a bicycle or an iron gate prevent corrosion?
- AIt turns the iron into a more reactive metal
- BIt keeps the iron surface from touching water and oxygen
- CIt makes a current flow through the iron
- DIt raises the oxidation number of the iron
Show the answer
Answer: B. It keeps the iron surface from touching water and oxygen
The answer is that it keeps the iron surface from touching water and oxygen. Iron needs both water and oxygen to rust, so covering the surface with paint or an oil film to block them prevents oxidation. It doesn’t work by changing the iron into another metal or by passing a current.
Remember: Paint prevents corrosion by ‘blocking’; a zinc block prevents it by ‘being oxidized instead’. Tell the two principles apart.
Did you know? In stainless steel, the chromium mixed into it forms a very thin oxide layer on the surface by itself, so it resists rust even without paint.
16.Which important industrial chemical is obtained by electrolyzing aqueous sodium chloride (salt water)?
- ASulfuric acid
- BAmmonia
- CNitric acid
- DSodium hydroxide
Show the answer
Answer: D. Sodium hydroxide
The answer is sodium hydroxide. When salt water is electrolyzed, 2H₂O + 2e⁻ → H₂ + 2OH⁻ at the (−) electrode produces hydrogen and OH⁻, which together with the remaining Na⁺ make sodium hydroxide. At the (+) electrode, Cl⁻ is oxidized to chlorine gas. Sulfuric acid, ammonia and nitric acid aren’t made in this process.
Remember: The three products of salt-water electrolysis are hydrogen, chlorine and sodium hydroxide.
Did you know? Sodium hydroxide is a raw material for making soap, and it’s also in cleaners used to unblock drains.
17.When iron is obtained from iron ore (iron oxide) in a blast furnace, what is the role of carbon monoxide (CO)?
- AAn oxidizing agent that oxidizes the iron
- BA reducing agent that reduces the iron oxide
- CA solvent that dissolves the iron
- DA negative catalyst that slows the reaction
Show the answer
Answer: B. A reducing agent that reduces the iron oxide
The answer is a reducing agent that reduces the iron oxide. In a blast furnace, the reaction Fe₂O₃ + 3CO → 2Fe + 3CO₂ happens. Carbon monoxide takes oxygen from the iron oxide, reducing it to iron, while it gains oxygen itself and is oxidized to carbon dioxide. Since it is oxidized itself, it is a reducing agent, not an oxidizing agent.
Remember: CO ‘gains’ oxygen to become CO₂, so it is oxidized itself, which makes it a reducing agent.
Did you know? Limestone added to the blast furnace combines with impurities in the ore, such as sand, to form ‘slag’, which floats to the top; this slag is reused as a raw material for cement.
18.In photosynthesis, when carbon dioxide is turned into glucose, what happens to carbon?
- AIt is reduced
- BThe element disappears
- CIts oxidation number doesn’t change
- DIt is oxidized
Show the answer
Answer: A. It is reduced
The answer is ‘it is reduced’. In CO₂, carbon’s oxidation number is +4, since x + 2 × (−2) = 0. In glucose, C₆H₁₂O₆, 6x + 12 × (+1) + 6 × (−2) = 0, so carbon’s average oxidation number is 0. The oxidation number decreases from +4 to 0, so carbon is reduced.
Remember: In photosynthesis carbon is reduced; in respiration carbon is oxidized.
Did you know? Most of the oxygen in Earth’s atmosphere was made by photosynthesis, and even today about half of it is produced by phytoplankton in the oceans.
19.In electrolysis, what reaction happens at the electrode connected to the (−) terminal of the power supply?
- AReduction
- BOxidation
- CNeutralization
- DCombustion
Show the answer
Answer: A. Reduction
The answer is reduction. The (−) terminal of the power supply pushes electrons into its electrode, so at this electrode, cations and other species gain electrons: reduction. For example, Cu²⁺ + 2e⁻ → Cu is a (−) electrode reaction. Oxidation happens at the (+) electrode, which pulls electrons away.
Remember: In electrolysis, the (−) electrode is where electrons come in, so it’s ‘reduction’.
Did you know? The word ‘ion’ comes from a Greek word meaning ‘going’. In 1834, Faraday gave this name to the particles that move toward the electrodes, on the suggestion of his colleague Whewell.
More Senior Chemistry II topics
States of Matter and Solutions · Enthalpy and Equilibrium · Reaction Rates and Catalysts
Other levels: Year 7 · Year 8 · Year 9 · Year 10 · Senior Chemistry I. Lesson plans: free worksheets.